A comprehensive treatment of current fastening technology using inserts (anchor channels, headed stud), anchors (metal expansion anchor, undercut anchor, bonded anchor, concrete screw and plastic anchor) as well as power actuated fasteners in concrete. It describes in detail the fastening elements as well as their effects and load-bearing capacities in cracked and non-cracked concrete. It further focuses on corrosion behaviour, fire resistance and characteristics with earthquakes and shocks. It finishes off with the design of fastenings according to the European Technical Approval Guideline (ETAG 001), the Final Draft of the CEN Technical Specification 'Design of fastenings for use in concrete' and the American Standards ACI 318-05, Appendix D and ACI 349-01, Appendix B.

A comprehensive treatment of current fastening technology using inserts (anchor channels, headed stud), anchors (metal expansion anchor, undercut anchor, bonded anchor, concrete screw and plastic anchor) as well as power actuated fasteners in concrete. It describes in detail the fastening elements as well as their effects and load-bearing capacities in cracked and non-cracked concrete. It further focuses on corrosion behaviour, fire resistance and characteristics with earthquakes and shocks. It finishes off with the design of fastenings according to the European Technical Approval Guideline (ETAG 001), the Final Draft of the CEN Technical Specification 'Design of fastenings for use in concrete' and the American Standards ACI 318-05, Appendix D and ACI 349-01, Appendix B.

Despite the widespread use of cast-in-place and post-installed anchors in construction, the overall level of understanding in the engineering community regarding their behaviour remains quite limited. Furthermore, since the publication of the original CEB design guide, “Design of Fastenings in Concrete”, ongoing research and additional application experience has led to an improved understanding and deepened knowledge in various areas of fastening technology. fib Bulletin 58 therefore represents a substantial revision of the original 1997 guide. It addresses a variety of loading types and failure modes and takes into account the current state of the art for anchorages in new construction as well as for their use in the repair and strengthening of existing concrete structures. fib Bulletin 58 provides a method for the design of the anchorage and additional rules for the design of the concrete member to which the load is transferred. The specified provisions are based on the currently available research.

As part of the preparation for the fib Model Code for Concrete Structures 2010, task group 4.5 Bond Models undertook a major review of rules for bond and anchorage of reinforcement in the CEB-FIP Model Code 1990. This bulletin presents the outcome of that review, describes the rationale for the revisions and presents the evidence on which the revisions are based. The principle changes in MC2010 include raising the limit on concrete strength that may be used when determining bond resistance to 110MPa, introduction of a coefficient η4 to cater for different reinforcement Classes, and coverage of new construction materials including epoxy coated and headed bars. The format of design rules has been changed to permit more rational treatment of confinement from concrete cover and transverse reinforcement, the contribution of end hooks and bends for tension bars, and end bearing to compression laps. New guidance is provided covering a range of construction techniques and service environments and the influence of long term degradation. Analyses of various aspects of detailing on performance of laps and anchorages have resulted in discontinuation of the ‘proportion lapped’ factor α6, alterations to requirements of transverse reinforcement at laps, and have resolved inconsistencies in provisions for bundled bars between major national codes. Apparent inconsistencies in existing rules for lapped joints and anchorages and between the local bond/slip model and design rules are also resolved, thus allowing integration of application rules and modelling. Finally, the basis for an attempt to introduce simple detailing rules for laps and anchorages is described.

Building with precast concrete elements is one of the most innovative forms of construction. This book serves as an introduction to this topic, including examples, and thus supplies all the information necessary for conceptual and detailed design.

The first edition of this comprehensive work quickly filled the need for an in-depth handbook on concrete construction engineering and technology. Living up to the standard set by its bestselling predecessor, this second edition of the Concrete Construction Engineering Handbook covers the entire range of issues pertaining to the construction

This book forms the Proceedings of the International Conference held in Vienna in November 1992 dealing with ageing, fatigue and fracture of concrete and concrete structures. Special sections cover demolition and recycling, and anchorage engineering. As well as selected international contributions, five specially invited plenary papers are included from Austria, Spain, Japan, Denmark and Sweden.

Here is a comprehensive guide and reference to assist civil engineers preparing for the Structural Engineer Examination. It offers 350 pages of text and 70 design problems with complete step-by-step solutions. Topics covered: Materials for Reinforced Concrete; Limit State Principles; Flexure of Reinforced Concrete Beams; Shear and Torsion of Concrete Beams; Bond and Anchorage; Design of Reinforced Concrete Columns; Design of Reinforced Concrete Slabs and Footings; Retaining Walls; and Piled Foundations. An index is provided.

The concrete industry has embraced innovation and ensured high levels of long-term performance and sustainability through creative applications in design and construction. As a construction material, the versatility of concrete and its intrinsic benefits mean it is still well placed to meet challenges of the construction industry. Indeed, concrete